--------------------------------------------------------------------- PARTNER Messaging Release 1.0 System Administration Version 1.0.0.9 ---------------------------------------------------------------------- 1. CONTENTS ---------------------------------------------------------------------- This file is organized into the following sections: 1. Contents This section lists the contents of this README file. 2. Overview This section gives an overview of the PARTNER Messaging System Administration software. 3. Removing the PARTNER Messaging System Administration Software This section describes how to remove the PARTNER Messaging System Administration software from your PC should this become necessary. 4. Installation Directory Organization This section gives information on the directory structure for where the application is installed. 5. Connecting to the PARTNER Messaging System This section describes the configuration that needs to take place to connect to a PARTNER Messaging system. 6. Solving Problems This section describes the problems you may encounter when installing and using PARTNER Messaging Administration. 7. To Get Help This section provides information on getting Help with the PARTNER Messaging System Administration software. ---------------------------------------------------------------------- 2. OVERVIEW ---------------------------------------------------------------------- The PARTNER Messaging Release 1.0 System Administration software can ONLY be used to administer a PARTNER Messaging Release 1.0 System. The software will not work with a previous release of the PARTNER Messaging System. PARTNER Messaging Administration requires an IBM PC-compatible with the following hardware and software: a) A Pentium ® 100 MHz or faster processor (A 200 MHz or faster processor is recommended.) b) A minimum of 32 MB of RAM for Microsoft Windows NT ® 4.0 Server or Workstation, a minimum of 16 MB of RAM for Microsoft Windows ® 98 or Microsoft Windows 95, a minimum of 64 MB of RAM for Microsoft Windows ® 2000 Workstation (128 MB is recommended). c) Windows ® 95, 98, NT 4.0 with Service Pack 4 (or later), or 2000 Workstation. d) 10 MB of hard disk space to install the application on your PC. However, you will need more space to back up the PARTNER Messaging system. Depending on the configuration of your PARTNER Messaging system, the backup size can range anywhere from few megabytes to few hundred megabytes. e) A network interface card with an RJ-45 connector. If your PARTNER Messaging system is connected to your company’s local area network (LAN), your PC must be connected to the LAN and you must have an account on your company’s LAN. If your PARTNER Messaging system is not connected to your company’s LAN, you will need a 10 Base-T crossover cable to connect your PC directly to the PARTNER Messaging system. f) A Windows-compatible VGA monitor supporting at least 256 colors and 800 x 600 pixel screen resolution. g) A Windows-compatible pointing device (for example, a mouse). h) A Windows-compatible multimedia sound card and speakers to listen to announcements. The sound card must be capable of playing and recording audio files in the Microsoft WAVE format. i) A microphone to record announcements. ---------------------------------------------------------------------- 3. REMOVING THE PARTNER MESSAGING SYSTEM ADMINISTRATION SOFTWARE ---------------------------------------------------------------------- If desired, the PARTNER Messaging System Administration software can be removed from your PC's hard disk using the "UnInstaller for System Administration" program link placed in the "Release 1.0 PARTNER Messaging" program group/application folder. You may choose to remove the files and program icons manually but there are many components to remove. Note: Uninstalling the software does not remove PARTNER Messaging backup(s) you may have created on the PC. ---------------------------------------------------------------------- 4. INSTALLATION DIRECTORY ORGANIZATION ---------------------------------------------------------------------- By default, the PARTNER Messaging Release 1.0 System Administration installation software installs the application in "C:\Program Files\PARTNER Messaging Release 1.0\System Administration" folder. However, during installation, you may choose to change the default installation directory. As part of the installation procedure, a folder named "Backups" is created in the installation directory. This folder is used as the default backup location for PARTNER Messaging backups you may create via the software. ---------------------------------------------------------------------- 5. CONNECTING TO THE PARTNER MESSAGING SYSTEM ---------------------------------------------------------------------- Before you can log into the PARTNER Messaging system, you must determine how your PC running the PARTNER Messaging Administration will connect to the PARTNER Messaging system. The PC can connect to the PARTNER Messaging system in either of the following ways: a) From an account on your company’s LAN b) Directly via a 10 Base-T crossover cable 5.1. Connecting to the PARTNER Messaging System via a LAN -------------------------------------------------------- To connect to the PARTNER Messaging system from your company’s LAN, the PARTNER Messaging system must be connected to the LAN. To connect the PARTNER Messaging system to the LAN, you will need: a) a 10 Base-T cable with an RJ-45 connector that is connected to your company’s LAN b) an available IP address on your company’s LAN that you will assign to the PARTNER Messaging system c) a PC with an RS-232 cable that you can connect to the PARTNER Messaging system and set the IP address for the PARTNER Messaging system. To connect the PARTNER Messaging system to the LAN: 1) Change the default LAN address of the PARTNER Messaging system to an available IP address on your company’s LAN. (See Instructions in Section 5.3.) 2) Connect the 10 Base-T cable from your company’s LAN to the RJ-45 connector on the PARTNER Messaging system. 5.2. Connecting Directly to the PARTNER Messaging System via a 10 Base-T Crossover Cable ------------------------------------------------------------- To connect a PC directly to the PARTNER Messaging system, you will need: a) a 10 Base-T crossover cable with an RJ-45 connector to connect the PC running PARTNER Messaging Administration to the PARTNER Messaging system. b) the IP addresses of the PARTNER Messaging system and the PC running PARTNER Messaging Administration to be in the same IP domain. Note: You can either change the default IP address of the PARTNER Messaging system to be in the same IP domain as the PC, or change the IP address of the PC to be in the same IP domain as the PARTNER Messaging system. Follow the instructions in Section 5.2.1 or 5.2.2 for more information. c) Once the PC and PARTNER Messaging system IP addresses are in the same domain, connect one end of the 10 Base-T crossover cable to the network interface card on the PC running PARTNER Messaging Administration. Connect the other end of the 10 Base-T crossover cable to the RJ-45 connector on the PARTNER Messaging system. 5.2.1. Changing your PC's IP Address ------------------------------------ If you choose to change your PC's IP address and leave in place the PARTNER Messaging default IP address, the IP address you assign must be in the same domain as the PARTNER Messaging default IP address (10.0.0.42). For example, you may choose to change the PC's IP address to 10.0.0.43. Follow the Windows IP address setup instructions on how to change your PC's IP address. 5.2.2. Changing your PARTNER Messaging System IP Address ------------------------------------------------------- If you want to keep the current IP address for the PC, you must change the IP address for the PARTNER Messaging system to an address that is in the same IP domain as the PC. For example, if the IP address of the PC is 192.17.127.70, set the IP address of the PARTNER Messaging system to 192.17.127.71. Follow instructions in Section 5.3 on how to the IP address of the PARTNER Messaging system. 5.3 Changing PARTNER Messaging System Default IP Address ------------------------------------------------------- 1) Connect the RS-232 cable from the PC to the RS-232 serial port on the PARTNER Messaging system. 2) Start a HyperTerminal session on the PC and a create a new connection. When "Port Settings" window is displayed, change the settings as follows: - Bit per second: 38400 - Data bits: 8 - Parity: None - Stop bits: 1 - Flow control: None 3) Log into the PARTNER Messaging system. 4) From the System Configuration Options menu, enter 4 and press the ENTER key. The IP Address Assignments menu appears. 5) Change the default LAN address of the PARTNER Messaging system to an available IP address on your company’s LAN. 6) Close the HyperTerminal session. 7) Disconnect the RS-232 serial cable from the PARTNER Messaging system. ---------------------------------------------------------------------- 6. SOLVING PROBLEMS ---------------------------------------------------------------------- Installation Problems --------------------- Problem 1: The Invalid Hardware Configuration message box appears. This message box appears if the PC screen resolution is lower than 800 x 600. PARTNER Messaging Administration requires a PC screen resolution of at least 800 x 600. Click the OK button, and then set the PC screen resolution to 800 x 600 or higher. Problem 2: The Application Already Installed! message box appears. This message box appears if PARTNER Messaging Administration is already installed on the PC. Click the OK button to close this message box. Usage Problems -------------- Problem 3: The Toolbar does not display properly. The Toolbar may not display properly if the display font size for your PC is set to Large Fonts. Change the display font size for your PC to Small Fonts. You can also access the Toolbar options from the Administration menu. Problem 4: The backup, restore, and upgrade procedures fail. The backup, restore, and upgrade procedures may fail if the screen saver is enabled and running on your PC. Disable the screen saver, and repeat the backup, restore, or upgrade procedure. ---------------------------------------------------------------------- 7. TO GET HELP ---------------------------------------------------------------------- PARTNER Messaging Administration contains an integrated Help file that can provide you with detailed information on all of the program’s features. From PARTNER Messaging System Administration software, press F1 for context-sensitive help. For more documentation on PARTNER Messaging administration, refer to the "PARTNER Messaging System Release 1.0 System Manager’s Quick Reference". For additional technical support, contact Avaya Inc. Technical Support Organization (TSO) Helpline or your local Authorized Avaya Dealer.